RJ11 RJ12 RJ45 All in One Tool For Pass Through EZ Legacy RJ45 Network Cable UTP STP Wire Crimping Tool
Modular-crimp connection for data and voice-over CAT3/CAT5e/CAT6/CAT7 applications. Create clean, flush trim on Pass-Through/EZ/Legacy RJ45 connectors. Reliable tool lets you cut, strip and crimp Ethernet and telephone cable. Compatible with all RJ45 CAT5e/CAT6 Pass-Through connectors (including shielded), and regular RJ11/RJ12 connectors (not AMP) Hardend Steel construction is durable and delivers more torque during the crimping cycle. Die head assembly provides 360 degrees of connector support for terminating modular plugs on stranded or solid cable. Blade Guard on cutting and stripping knives reduces risk of injury and helps maintain razor sharpness. Textured handle grips reduce hand fatigue and prevent slipping during cutting, stripping and crimping. If you aren’t impressed with the durability and performance of Platinum Connector RJ45 Crimping Tool.
- Multifunction - Used for pass through design connectors , crimp the connector and cut the extra wires , another function of crimping dovetail clip, which is helpful for crimping modular plugs with feed-thru design and dovetail clip at the same time
- High Precision - High-standard precision crimping and grinding port, fixed modular plugs to make sure cables do not fall.
- CAT5 CAT6 CAT7 Modular Crimper - It doesn’t matter whether you are an IT professional who is dealing with network cables and connectors daily or just a home user who is a newbie to the Ethernet network, you should get the Microware Ethernet crimping tool. 2/3 the size of traditional crimpers, come with screwdriver and cable stripper, crimps standard CAT5 CAT6 and shielded CAT7 network connectors and budget friendly; all together make this network tool from Microware is a top-ranked RJ45 RJ12 RJ11 network crimper today.
- Built for Pass-thru Network Connectors - Crimps RJ45 (Data) and RJ12 RJ11 (Voice) fixed die cavities, supports Cat5 Cat5e Cat6 Cat7 Ethernet STP/UTP cables, twisted pairs, phone, voice and data cables crimping.
- Built for Dovetail Clip - Specially design for Cat6a Cat7 shielded connectors and even crimp the metal clip on the plugs.
- Built-in Cat7 to Cat5 Switcher -Switch from Cat7 to Cat5 crimping by using a screwdriver to loosen then switch up or down to change the compression mode. The Cat7 mode stands for Cat7 and Cat6a shielded plugs crimping. Cat5 mode stands for Cat5, Cat5e and Cat6 plugs crimping.
Strip and cut the cable
Strip the cable back 1 inch (25 mm) from the end. Insert the cable into the stripper section (round hole) then rotate the crimping tool around the cable to create a clean cut then remove the sheathing. Untwist and straighten the wires inside of the cable, cut off the small plastic wire separator or core so it’s out of the way and cut the wires into an even line 1⁄2 inch (13 mm) from sheathing.
Insert the wires to connector
Insert the wires into the RJ45 connector with right orders (T568A/B), then insert the cable into the connector so that each of the small wires fits into the small grooves in the connector. The sheathing of the cable should fit just inside of the connector so it’s past the base. Each wire must fit into a groove before you crimp the connector.
Full-cycle connector crimping
Stick the connector into the crimping part of the tool and squeeze twice. Insert the connector in the crimping section of the tool until it can’t fit any further. Squeeze the handles to crimp the connector and secure the wires. Release the handles, then squeeze the tool again to make sure all of the pins are pushed down.
Test the cable and done
Use the Microware network cable tester will help you save time and effort – Powered by 6F22 9V 25MA battery (which is not included), come with user manual and instruction. LED display with power switch, scanning mode switch and test switch for manual scan. Verify cable continuity, open short and miswiring, with remote kit, test on wall plate, patch panel and test grounding.
